The “ON” or “OFF” under the “SLEEP” at the right bottom corner will illuminate correspondingly. Press ALARM SET button repeatedly to change the sleep time from OFF, 15, 30, 45 or 60 minutes. With the number representing the minutes (SLEEP 15). To set the Sleep Time, press the ALARM SET button (24) and the sleep time will be displayed ![]() The Sleep Timer will automatically turn off the JWM6A in the designated number of minutes. If the new alarm time is not confirmed by pressing the ENTER SEARCH button, the unit will automatically exit the alarm setting menu after 10 seconds of inactivity and the new alarm time will be set. The “ALARM” on the LCD display will illuminate correspondingly. Press the ALARM ON/OFF button to turn the alarm on or off. Press the ENTER SEARCH button to save the new alarm time and exit the alarm setting menu. Continue adjusting the hour to move from AM to PM. Press the |>| button (16) to adjust the minute of the alarm time. To set the alarm, press and hold the ALARM SET button (24) for 2 seconds and the clock digits will be flashing. LO BAT ALERT (On/Off): Monitor voltage on ACC line and send alert when voltage is low.īluetooth Device (Lock/Unlock, Disconnect/Connect, Delete): View, lock and delete from a list of previously paired mobile phone device models.īluetooth Pair: Choose “ENTER” to automatically pair a device. Region (USA/Europe): Set frequency spacing for various regions. BRI(off,1,2,3,4): Adjust the brightness of the LCD backlight from the following levels: 4,3,2,1 or off.Note: Beep tone off will not affect the audible tone of the alarm clock. The unit will automatically exit the audio menu after 10 seconds of inactivity.īeep On/Off: Turn the audible beep On/Off (heard when functions/buttons are selected). Press the ENTER SEARCH button to confirm your selection and exit audio menu. Once the desired menu item appears on the display, adjust that option by rotating the volume encoder knob clockwise or counter-clockwise within 10 seconds.Ĥ. Press the |>| buttons (15, 16) or AUDIO MENU button repeatedly to navigate the system menu.ģ. Press and hold the AUDIO MENU button (18) for 2 seconds to enter the system menu.Ģ. You can navigate through the audio menu items by pressing the >| or | CLASSICAL > ROCK > FLAT.ġ. Press the AUDIO MENU button (18) to access the audio menu.Ģ. Mount the unit using four M3x20mm (3/32 x 0.75”) screwsġ. Route power, speakers, AV, and antenna cables through the hole and connect ![]() Use the mounting hole diagram to measure and cut a mounting hole Places exposed to heat-radiating appliances such as electric heatersĪdjacent to other equipment that radiates heat Select a mounting location, taking care to avoid the following: Under these conditions, use extra caution during installation to avoid causing a short circuit. If the cable is disconnected, the computer memory may be lost. NOTE: If the JWM6A is to be installed in a vehicle equipped with an on-board drive or navigation computer, do not disconnect the battery cable. To prevent a short circuit, be sure to turn off the ignition and remove the negative (-) battery cable prior to installation. Tools to remove existing radio (screwdriver, socket wrench set or other tools) You will need these tools and supplies to install your JWM6A: Location is clear of wires, fuel and vacuum or brake lines. Having your Jensen JWM6A installed by a reputable RV dealership NOTE: Before cutting the mounting hole, make sure the area behind the mounting It’s a good idea to read all of the instructions before beginning the installation. To reduce the risk of fire or electric shock, do not expose this equipment to rain or moisture. Failure to observe this may cause malfunction due to the precise mechanism of this unit.ĭo not attempt to disassemble or adjust this precision product contact a professional for assistance. This product is designed to operate with a 12 volt DC, negative ground battery system (the standard system in a North American vehicle).Īvoid inserting any foreign objects into the slot of this player. Pre-set Equalizer - 5 settings (User > Flat > Pop > Classical > Rock)Įlectronic Bass, Treble, Balance and Fader Controls ![]() įeatures of Jensen JWM6A mobile audio system include:ĭigital AM/FM Tuner/30 Preset stations (12 AM/18 FM)īluetooth Ready with A2DP/AVRCP Streaming Audio Tuner Operation.ĭisc Operation.ĬD Operation.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |